Siteworks

Installation and decommission management

Hotel Energy offers bespoke ‘end to end’ siteworks management for your growing business. From new utility installations for renovated and newly built business premises, through to the decommissioning of meters and supply lines, our dedicated siteworks team will help you complete your next project.

Our siteworks management services will prove to be a valuable asset to your business’s next development by ensuring that your deadlines are met and costs kept under control throughout your entire energy installation and decommissioning projects.

  • “One of our clients informed us about Hotel Energy as being the key company within the supply chain to manage utility services. It has been an absolute pleasure to work with Hotel Energy as they deal with the uncertain and potential risks to the project’s completion date with their professional & prompt service.”

    ISG Interior/Exterior Divisional Building Services Manager

Book Siteworks

Call 0845 872 8724 or get an online quote below

Contact Details
About Your Project

Have you previously received a quotation for this project?

Do you wish Hotel Energy to perform on site excavation and reinstatement?

Property Type

Electrical Load Requirements
No. of connections required Load (kVA)
No. of connections required Load (kVA)
No. of connections required Load (kVA)
No. of connections required Load (kVA)
Heating Type Specify
Disturbing Load Details (if applicable)

In order to perform accurate network analysis, please provide details of equipment such as large motors, welding equipment which may exert excessive load that may be detrimental to other customers.

 

Motors
Total single phase motors in kW
Largest single phase motor in kW Type of Starting
Frequency of starting (per hour) Starting current (in AMPS)
Total 3 phase motor in kW Type of Starting
Frequency of starting (per hour) Starting current (in AMPS)
Welding Equipment
Total welding equipment in kVA
Maximum current from mains (in AMPS)
Maximum Power
2
Total maximum power required in kVA
If this exceeds 299kVA you are required to provide a full load breakdown.
Will generation equipment be installed?
kVA required at each meter point
Specify
Existing Supplies Information
MPAN
Current Supplier
Please provide any additional information that may be relevant to your application

For help filling out this application or any further queries please call 08454891011

 

Please be advised a quotation can take up to 3 weeks as we have to consider any embargoes, traffic easements and we have to gain DNO approval to adopt onto their network.

 

Siteworks Information – what it is and why we need it

MPAN (existing services only) - this is the unique Meter Point Account Number (MPAN) for any existing service. This information will help us to trace the existing installation and where known, determine the size and capacity of the existing meter. The MPAN can be found on your Electric bill. AAQ – this is the maximum annual electric load you will be expecting to use through your meter in a single year, based on the maximum capacity of the Electric appliances you are planning to have on site. A Qualified Electrician will be able to help you determine this. This information will enable Hotel Energy to accurately order the correct amount of electricity is available at your meter point.

PID – this is the maximum hourly electricity load you will be expecting to use through your meter in a single hour, based on the maximum capacity of the electricity appliances you are planning to have on site. A qualified Electrician will be able to help you determine this. This information will be used to determine the size of the meter required, and the size of the cable required to meet the demand.

Please note that for alterations we still need to know the PID and AAQ. If your alteration affects the length of the cable, this can affect the diameter of the cable also. For increases in capacity, we need to know the existing PID and AAQ as well as the increased PID and AAQ. This must be based on the equipment that is on site and not based on the amount of electricity stated on the bill. The electricity company requires these figures to reduce the risk to the existing gas network.

HH/Non HH – Supplies under 100kVa tend to be Non –Half Hourly (NHH) metered, using standard meters that are read manually. Sites with a peak load above 100KW need to be equipped with “half-hourly” meters which record total consumption every half-hour and pass the information to the energy supplier. If you have an HH meter it’s mandatory to appoint a Meter Operator (MOP) and Data Collector (DC) for your site. These companies are separate from your electric supply through your supplier.

Meter Operator- A Meter Operator (MOP) is responsible for installing and maintaining metering and communication equipment, and provides the technical meter details to the Data Collector to enable consumption data collection.

Data Collector – A Data Collector (DC) is an organisation appointed by the supplier and accredited to carry out Data Collection for Half- Hourly Metering Systems. Metering data is collected and validated by the DC and forwarded to the Data Aggregator, who applies additional factors before sending it to the supplier. The supplier is responsible for maintaining the level of service up to or above 99% of actual data. This is an industry requirement.

Whole Current Meter – single phase meter used to measure AC mains current in which the whole current to be measured flows directly through the meter. CT Meters- electricity meter where the electricity flows through a Current Transformer which reduces the electricity to flow through the meter by a defined ratio. The ratio can be found on the cabling quote for the new building or on the transformer itself.

Current Supplier
Site Details
Works Required

Nature of Works

Additional Works

Housing Required

Excavations

MPRN (Meter Point Reference Number) - Required for all works except New Service
Meter Serial Number
Consumption Details
AAQ (Annual)
PID (Hourly) - Required Daily
Existing   kWh   kWh   kWh
Additional   kWh   kWh   kWh
Total New Load   kWh   kWh   kWh
If the request is for meter only and PID is above 1,083kWh please select ECV orientation:

Outlet pressure greater than 19mb required?

If yes above, please specify

Service Pressure

Load Type

ECV diameter (mm/inch)

Preferred Completion Date

Project Co-ordinator (Who we contact to confirm information and dates)
Payee (Responsible for the payment of works)
Gas Consumer (Responsible for the payment of the gas supply contact)
Emergency Site Contact

For help filling out this application or any further queries please call 08454891011

 

Please be advised a quotation can take up to 3 weeks as we have to consider any embargoes, traffic easements and we have to gain DNO approval to adopt onto their network.

 

Siteworks Information – what it is and why we need it

MPAN (existing services only) - this is the unique Meter Point Account Number (MPAN) for any existing service. This information will help us to trace the existing installation and where known, determine the size and capacity of the existing meter. The MPAN can be found on your Electric bill. AAQ – this is the maximum annual electric load you will be expecting to use through your meter in a single year, based on the maximum capacity of the Electric appliances you are planning to have on site. A Qualified Electrician will be able to help you determine this. This information will enable Hotel Energy to accurately order the correct amount of electricity is available at your meter point.

PID – this is the maximum hourly electricity load you will be expecting to use through your meter in a single hour, based on the maximum capacity of the electricity appliances you are planning to have on site. A qualified Electrician will be able to help you determine this. This information will be used to determine the size of the meter required, and the size of the cable required to meet the demand.

Please note that for alterations we still need to know the PID and AAQ. If your alteration affects the length of the cable, this can affect the diameter of the cable also. For increases in capacity, we need to know the existing PID and AAQ as well as the increased PID and AAQ. This must be based on the equipment that is on site and not based on the amount of electricity stated on the bill. The electricity company requires these figures to reduce the risk to the existing gas network.

HH/Non HH – Supplies under 100kVa tend to be Non –Half Hourly (NHH) metered, using standard meters that are read manually. Sites with a peak load above 100KW need to be equipped with “half-hourly” meters which record total consumption every half-hour and pass the information to the energy supplier. If you have an HH meter it’s mandatory to appoint a Meter Operator (MOP) and Data Collector (DC) for your site. These companies are separate from your electric supply through your supplier.

Meter Operator- A Meter Operator (MOP) is responsible for installing and maintaining metering and communication equipment, and provides the technical meter details to the Data Collector to enable consumption data collection.

Data Collector – A Data Collector (DC) is an organisation appointed by the supplier and accredited to carry out Data Collection for Half- Hourly Metering Systems. Metering data is collected and validated by the DC and forwarded to the Data Aggregator, who applies additional factors before sending it to the supplier. The supplier is responsible for maintaining the level of service up to or above 99% of actual data. This is an industry requirement.

Whole Current Meter – single phase meter used to measure AC mains current in which the whole current to be measured flows directly through the meter. CT Meters- electricity meter where the electricity flows through a Current Transformer which reduces the electricity to flow through the meter by a defined ratio. The ratio can be found on the cabling quote for the new building or on the transformer itself.

To validate this form please complete our logo: Hotel